Addressable media channels, separated by chambers into which an ECM-mimicking gel can be injected (Fig. 1a). Details of the design and the steps required for fabrication of the systems in PDMS have been described previously [25,28,30]. In brief, the microfluidics system consists of molded PDMS (poly-dimethyl siloxane; Silgard 184; Dow Chemical, MI) through which access ports are bored and bonded to a cover glass to form a microfluidic channels. Channel cross-sectional dimensions are 1 mm (width) by 120 mm (height). The PDMS layer is formed from a patterned SU8 photoresist on a silicon wafer using soft-lithography. To enhance matrix adhesion, the PDMS channels are coated with a PDL (poly-D-lysine hydrobromide; 1 mg/ml; Sigma-Aldrich, St. Louis, MO) solution. Next, collagen type I (BD Biosciences, San Jose, CA, USA) solution (2.0 mg/ml) with phosphate-buffered saline (PBS; Gibco) 23727046 and NaOH is injected into the gel regions of the device via 4 separate filling ports using a 10 ml pipette and incubated for 30 min to form a hydrogel, chosen to represent ECM in 3D space. When the gel is polymerized, endothelial cell medium is immediately pipetted into the channels to prevent dehydration of the gel. Upon aspirating the medium, diluted MatrigelTM (BD science) solution (3.0 mg/ml) is introduced into the cell channel and the excess MatrigelTM solution is washed away 1 minute laterIn Vitro Model of Tumor Cell Extravasationusing cold medium. 2D top and face views of the device are shown in Fig. 1b to show how this microfluidic system is used to model extravasation. Endothelial cells are first introduced to cover the entire Clavulanate (potassium) chemical information middle channel and later cancer cells are introduced so they adhere to and transmigrate across the already formed endothelium into the gel region. The middle channel acts as a cell channel where both endothelial cells and cancer cells are introduced to form a monolayer and transmigrate, respectively.Cell Culture and Cell SelectionHuman microvascular endothelial cells (hMVECs) were commercially obtained (Lonza) and cultured in endothelial growth medium (EGM-2MV, Lonza). Cells were cultured in standard culture flasks and the medium was changed every two days until seeding. During the Licochalcone A supplier seeding process, 40 ml of hMVEC suspension at 26106 cells/ml was introduced into the prepared microfluidic device. The cells were kept in a 37uC incubator for 1 hour to allow the adhesion of cells to the collagen scaffold wall. All experiments were conducted using hMVECs of passage 8 or lower. Human mammary adenocarcinoma cells 1317923 (MDA-MB-231) were chosen due to their invasiveness and their ability to metastasize in vivo [32,33]. A GFP-expressing version of the MDA-MB-231 cell line (provided by F. Gertler, MIT) enabled live-cell imaging via fluorescent microscopy. Cancer cell lines were cultured in standard DMEM media (Sigma) with 10 fetal bovine serum (Invitrogen) and antibiotics. The human mammary epithelial cell line MCF-10A (provided by Brugge Lab, Harvard Medical School) was cultured as described previously [34]. Two days after endothelial cell seeding, tumor cells were introduced into the same channel where endothelial cells had formed a complete monolayer. Culture flasks containing the tumor cells were first washed with PBS and the cells were later trypsinized for 5 min to make the cell suspension in cancer cell medium. For seeding, 40 ml of 50000 cells/ml tumor cell suspension medium was placed in one side of the channel reservoir and left to equi.Addressable media channels, separated by chambers into which an ECM-mimicking gel can be injected (Fig. 1a). Details of the design and the steps required for fabrication of the systems in PDMS have been described previously [25,28,30]. In brief, the microfluidics system consists of molded PDMS (poly-dimethyl siloxane; Silgard 184; Dow Chemical, MI) through which access ports are bored and bonded to a cover glass to form a microfluidic channels. Channel cross-sectional dimensions are 1 mm (width) by 120 mm (height). The PDMS layer is formed from a patterned SU8 photoresist on a silicon wafer using soft-lithography. To enhance matrix adhesion, the PDMS channels are coated with a PDL (poly-D-lysine hydrobromide; 1 mg/ml; Sigma-Aldrich, St. Louis, MO) solution. Next, collagen type I (BD Biosciences, San Jose, CA, USA) solution (2.0 mg/ml) with phosphate-buffered saline (PBS; Gibco) 23727046 and NaOH is injected into the gel regions of the device via 4 separate filling ports using a 10 ml pipette and incubated for 30 min to form a hydrogel, chosen to represent ECM in 3D space. When the gel is polymerized, endothelial cell medium is immediately pipetted into the channels to prevent dehydration of the gel. Upon aspirating the medium, diluted MatrigelTM (BD science) solution (3.0 mg/ml) is introduced into the cell channel and the excess MatrigelTM solution is washed away 1 minute laterIn Vitro Model of Tumor Cell Extravasationusing cold medium. 2D top and face views of the device are shown in Fig. 1b to show how this microfluidic system is used to model extravasation. Endothelial cells are first introduced to cover the entire middle channel and later cancer cells are introduced so they adhere to and transmigrate across the already formed endothelium into the gel region. The middle channel acts as a cell channel where both endothelial cells and cancer cells are introduced to form a monolayer and transmigrate, respectively.Cell Culture and Cell SelectionHuman microvascular endothelial cells (hMVECs) were commercially obtained (Lonza) and cultured in endothelial growth medium (EGM-2MV, Lonza). Cells were cultured in standard culture flasks and the medium was changed every two days until seeding. During the seeding process, 40 ml of hMVEC suspension at 26106 cells/ml was introduced into the prepared microfluidic device. The cells were kept in a 37uC incubator for 1 hour to allow the adhesion of cells to the collagen scaffold wall. All experiments were conducted using hMVECs of passage 8 or lower. Human mammary adenocarcinoma cells 1317923 (MDA-MB-231) were chosen due to their invasiveness and their ability to metastasize in vivo [32,33]. A GFP-expressing version of the MDA-MB-231 cell line (provided by F. Gertler, MIT) enabled live-cell imaging via fluorescent microscopy. Cancer cell lines were cultured in standard DMEM media (Sigma) with 10 fetal bovine serum (Invitrogen) and antibiotics. The human mammary epithelial cell line MCF-10A (provided by Brugge Lab, Harvard Medical School) was cultured as described previously [34]. Two days after endothelial cell seeding, tumor cells were introduced into the same channel where endothelial cells had formed a complete monolayer. Culture flasks containing the tumor cells were first washed with PBS and the cells were later trypsinized for 5 min to make the cell suspension in cancer cell medium. For seeding, 40 ml of 50000 cells/ml tumor cell suspension medium was placed in one side of the channel reservoir and left to equi.
